Altronix T1MK1F4S Access and Power Integration Kit

Altronix T1MK1F4S Access and Power Integration Kit

Altronix T1MK1F4S Trove Mercury kit is pre-assembled and consists of Trove1M1 enclosure/ backplane with factory installed Altronix power supply/charger and sub-assemblies. This kit also accommodates various combinations of Mercury boards for up to four (4) doors in a single enclosure. Trove simplifies board layout and wire management, reduces installation time and labor costs.

Key Features:

• Power Supply (eFlow4NB):

  • Input

    • Voltage: 120VAC, 60Hz.
    • Fusing: 5A / 250V.

  • Output

    • Voltage: 24VDC.
    • Current: 4A continuous.
    • Other: Overvoltage protection. Filtered and regulated.

• Battery Backup

  • Capacity: 7AH / 12VDC (Up to 2 within enclosure). 40 AH / 65 AH (requires separate enclosure).
  • Type: Sealed lead acid or gel type.
  • Fuse: Rating 10A/32V.
  • Failover: Upon AC loss, instantaneous.

• Supervision

  • AC Failure: Form “C” contacts.
  • Battery: Form “C” contacts.
  • Low DC Power Shutdown: Shuts down DC output terminals if battery voltage drops below 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge.

• Indicators LED

  • Input: 120VAC is present.
  • DC Output: Powered.
  • Battery: Discharged or not connected.

• Voltage Regulator (VR6):

  • Input

    • Voltage: 24VDC from eFlow4NB.

  • Output

    • Voltage: 12VDC.
    • Current: 6A continuous.
    • Other: Surge suppression.

  • Indicators (LED)

    • Input: 24VDC is present.
    • Output: Powered.

• Access Power Controller (ACM4):

  • Input

    • Voltage: 24VDC from eFlow4NB.
    • Fusing: 10A / 250V.

  • Output

    • Voltage: 24VDC.
    • Four (4) independently controlled 2.5A outputs:
    • a) Four (4) Fail-Safe and/or Fail-Secure power outputs.
    • b) Four (4) dry form “C” 5A rated relay outputs.
    • c) Any combination of the above.
    • Four (4) auxiliary power outputs (unswitched).

  • Outputs Ratings

    • Fuses: 3A / 32VDC.

  • Indicators (LED)

    • Red LEDs: Outputs are triggered (relays energized).
    • Green LED: FACP disconnect is triggered.

• Dual Input Power Distribution Module (PDS8):

  • Input

    • Voltage: 12VDC from VR6 and 24VDC from eFlow4NB.
    • Main Fuse Rating: 10A.

  • Output

    • Voltage: 12VDC and/or 24VDC.
    • Any of the eight (8) fuse protected power outputs are selectable to follow power Input 1 or Input 2.
    • Individual outputs may be set to OFF position for servicing.

  • Outputs Ratings

    • Fuses: 3A / 250V.

  • Indicators (LED)

    • DC Output: Eight (8) individual output LEDs.

• Physical and Environmental (T1MK1F4S):

  • Temperature

    • Operating: 0° C to 49° C (32° F to 120° F).
    • Storage: - 20° C to 70° C ( - 4° F to 158° F).

  • Relative Humidity

    • Relative Humidity 85% +/- 5%.

  • BTU/Hr (approx.):

    • 90 BTU/Hr.