Altronix T1RAL3F8 Access and Power Integration Kit

Altronix T1RAL3F8 Access and Power Integration Kit

Altronix T1RAL3F8 rack kit is pre-assembled and consists of Trove1AL1R enclosure/backplane with factory installed Altronix power supply/ charger(s) and sub-assemblies.

Key Features:

• Power Supply (eFlow6NB):

  • Input

    • Voltage: 120VAC, 60Hz, 3.5A max.
    • Fusing: 5A / 250V.

  • Output

    • Voltage: Factory set at 24VDC.
    • Current: 6A continuous.
    • Maximum Supply Current for Main and Aux. Outputs on eFlow6NB Power Supply board, ACMS8 Access Power Controller’s and PDS8 Power Distribution Module’s outputs is 5.6A.
    • Auxiliary: Class 2 power-limited @ 1A (unswitched).
    • Other: Overvoltage protection. Filtered and regulated.

• Battery Backup

  • Built-in charger for sealed lead acid or gel type batteries (if batteries are required, install separate battery enclosure RE2).
  • Automatic switch over to stand-by battery when AC fails.
  • Zero voltage drop when unit switches over to battery backup (AC failure condition).

• Fire Alarm Disconnect

  • Supervised: Latching or non latching.
  • EOL: 10K Resistor.

• Supervision

  • AC Failure: Form “C” contacts.
  • Battery: Form “C” contacts.
  • Low DC Power Shutdown: Shuts down DC output terminals if battery voltage drops below 70-75% for 24V units. Prevents deep battery discharge.

• Indicators LED

  • Input: 120VAC is present.
  • DC Output: Powered.
  • Battery: Discharged or not connected.

• Power Distribution Module (PDS8):

  • Input

    • Voltage: 24VDC from eFlow6NB and 12VDC from VR6.
    • Fusing: 10A / 250V.

  • Output

    • Voltage: 12 or 24VDC individually selectable.
    • Fuses Rating: 3A / 32VDC.

  • Indicators (LED's)

    • DC Output: Eight (8) individual output LEDs.

• Access Power Controller (ACMS8):

  • Input

    • Voltage: 24VDC from eFlow6NB and 12VDC from VR6.
    • Fusing: 15A / 32V.

  • Output

    • Voltage: 12 or 24VDC individually selectable.
    • Eight (8) selectable 12VDC - 24VDC independently controlled outputs or eight (8) indepently controlled Form “C” relay outputs:
    • a) Fail-Safe and/or Fail-Secure power outputs.
    • b) Form “C” Relays. 28VAC or VDC @ 2.5A Rated.
    • c) Auxiliary power outputs (unswitched).
    • d) Any combination of the above.
    • Any of the eight (8) fuse protected power outputs are selectable to follow power Input 1 or Input 2.
    • Individual outputs may be set to OFF position for servicing.
    • Fuses Rating: 2.5A / 32VDC.

  • Indicators (LED)

    • Red LEDs: Outputs are triggered (relays energized).
    • Blue LED: FACP disconnect is triggered.

  • Individual voltage LEDs

    • Green: 12VDC
    • Red/Green: 24VDC

• Physical and Environmental (T1RAL3F8):

  • Temperature

    • Operating: 0° C to 49° C (32° F to 120° F).
    • Storage: - 20° C to 70° C ( - 4° F to 158° F).

  • Relative Humidity

    • Relative Humidity 85% +/- 5%.

  • BTU/Hr (approx.):

    • 115 BTU/Hr.